Keller Dovetail System - Journeyman model 2200 - 22 inch
SKU:
$239.00
$6.00 - $239.00
per item
The larger 2200 model cuts dovetails for larger furniture, cabinets, casegoods, fixtures, and chests. The double sided template comes with two router bits each with shank mounted bearings, and instructions.
All models include:
A. Precision templates (one double sided type for journeyman models - two single sided type for professional models).
B. Two carbide-tipped router bits (standard dimensions)... One dovetail bit and one straight cutting bit.
C. Two ball bearing template guides mounted on each router bit shank.
D. Fully illustrated instruction manual.
Each template requires a simple wooden backing block (not included)
Wood Width Capacity:……………….. Unlimited
Length of Templates:…………………………… 22″
Wood Thickness Capacity:……………….. 1/4″-1″
-with Rabbeted Pins:………………….. Up to 11/2″
Dovetail Angle:……………………. 7 degree (8:1)
Pin Spacing, center to center:………………. 13/4″
Minimum Router hp Required:………….. 11/4 hp
Router Collet Size Required:…………..1/2″ or 3/8″
Shipping Weight:……………………………….3 lbs
Spend less time adjusting tools.
Engineered for simplicity.
Just clamp the Keller Dovetail Templates to your workpiece, pick up your router, and start cutting.
In 2 to 5 minutes you'll cut both halves of a dovetail joint.
The results will be clean, precise, and snug fitting, with beautiful hand-cut proportions.
Cut any width of stock, and vary your wood thicknesses easily…
All models give you through-dovetail joints in any width of stock.
No built-in stops to limit the width of your work.
If your work is wider than your templates, just slide the templates along and continue cutting.
Keller gives you a consistently tight dovetail joint regardless of the wood thickness or the router bit setting.
No readjustments and test cuts every time you change your wood thickness. Also, you can join wood of the same or different thicknesses with the same setup.
For Production Runs or Unique Heirlooms…
A. Precision templates (one double sided type for journeyman models - two single sided type for professional models).
B. Two carbide-tipped router bits (standard dimensions)... One dovetail bit and one straight cutting bit.
C. Two ball bearing template guides mounted on each router bit shank.
D. Fully illustrated instruction manual.
Each template requires a simple wooden backing block (not included)
Wood Width Capacity:……………….. Unlimited
Length of Templates:…………………………… 22″
Wood Thickness Capacity:……………….. 1/4″-1″
-with Rabbeted Pins:………………….. Up to 11/2″
Dovetail Angle:……………………. 7 degree (8:1)
Pin Spacing, center to center:………………. 13/4″
Minimum Router hp Required:………….. 11/4 hp
Router Collet Size Required:…………..1/2″ or 3/8″
Shipping Weight:……………………………….3 lbs
Spend less time adjusting tools.
Engineered for simplicity.
Just clamp the Keller Dovetail Templates to your workpiece, pick up your router, and start cutting.
In 2 to 5 minutes you'll cut both halves of a dovetail joint.
The results will be clean, precise, and snug fitting, with beautiful hand-cut proportions.
Cut any width of stock, and vary your wood thicknesses easily…
All models give you through-dovetail joints in any width of stock.
No built-in stops to limit the width of your work.
If your work is wider than your templates, just slide the templates along and continue cutting.
Keller gives you a consistently tight dovetail joint regardless of the wood thickness or the router bit setting.
No readjustments and test cuts every time you change your wood thickness. Also, you can join wood of the same or different thicknesses with the same setup.
For Production Runs or Unique Heirlooms…
